<![CDATA[<body bgcolor="#FCE9F2">
<p><font color="#FCE9F2" size="-4">
PRODUCT DESCRIPTION PINK glass fibre thermal insulation, inorganic, pre-formed unfaced blankets, designed for friction-fit installation in frame cavities. Recommended Uses Glass fibre thermal insulation blankets may be installed in the following locations: Above ground steel or wood stud framed exterior walls. Interior side of below ground foundation walls with steel or wood framing. Floors above unheated exterior spaces and crawl spaces. Ventilated roof-spaces (or attics) above flat or sloped ceilings. Steel or wood stud framed roof parapets and curbs. Cathedral ceilings. Steel or wood stud framed interior partitions separating heated spaces from unheated or refrigerated spaces. To provide thermal resistance around openings in a building's exterior envelope. Glass fibre thermal insulation is GREENGUARD and SCS certified "Post-consumer": glass materials recycled from construction sites (demolition work, new construction and renovation) and from consumers' "blue boxes". "Post-industrial" (or "preconsumer"): glass recycled from glass manufacturing plants' waste (glass containers, flat glass and others). Includes materials that contribute to the reduction of dust and static electricity, ensuring a clean and easy installation. TECHNICAL DATA Applicable Codes and Standards National Building Code of Canada 1995 Meets requirements of article 9.25.2.2. and 5.3.1.2.(2) (including all subsequent revisions). Canadian Standards (Underwriters Laboratories of Canada (ULC)) CAN/ULC-S702, Standard for Thermal Insulation, Mineral Fibre, for Buildings (supersedes CSA A101-M1983); Type 1, pre-formed unfaced insulation. CAN/ULC-S102.2, Standard Method of Test for Surface Burning Characteristics of Building Materials and Assemblies. CAN4-S114-M80, Standard test method to determine the incombustibility of building materials; Type 1 pre-formed glass fibre thermal insulation (with the exception of RSI 2.4 and RSI 3.87) meets the requirements of this standard. Health Canada/Workplace Hazardous Materials Information System (WHMIS). Visit www.owenscorning.ca for a current copy of the Material Safety Data Sheet (MSDS) for "Low Density Fiber Glass Insulation - unfaced". for its "green" content (refer to TECHNICAL DATA) and can contribute to obtaining LEEDTM Certification credits when used as thermal insulation in a building submitted to the LEED CANADA-NC Green Building Rating System (refer to TABLE 2). Limitations Owens Corning does not recommend using PINK FIBERGLAS Thermal Insulation in the following locations: On the exterior side of intermediate sheathing of cavity walls and other locations exposed to water, humidity and wind. On the exterior side of foundation walls, whether above or below ground level. In locations where no vapour retarder is provided on the warm side of the insulation. Where it is impossible to provide clearances required by Codes and Regulations (building, electrical, gas and oil) between the insulation and heat-emitting appliances, chimneys, pipes, conduits and vents to these appliances (at least 50 mm) and between insulation and recessed light fixtures that are not encased in CSA-approved insulated boxes (at least 75 mm). PINK FIBERGLAS Thermal Insulation can also enhance the acoustical performance of an acoustic separation, but Owens Corning recommends using QuietZone Acoustic Batt Insulation; see QUIETZONE Data Sheet 09 81 16.16.OCC QUIETZONE. Components PINK-colour, bonded glass fibre, manufactured from recycled materials obtained from two sources: Product Data Sheet 07 21 16.16.OCC PINK FIBERGLAS Thermal Batt Insulation Properties Thermal resistance Thickness Width Length Surface burning characteristics Smoulder resistance (1) Refer to CAN/ULC-S702, TABLE 2 07 21 16.16.OCC PINK FIBERGLAS Thermal Batt Insulation Product Data Sheet TABLE 1 - CAN/ULC-S702 Physical Property Requirements CAN/ULC-S702 requirements for pre-formed unfaced insulation(1). Mean thermal resistance the design thermal resistance (as stated on the product). Mean thickness design thickness and none of the individual thickness less than 90% of the design thickness. - 0%, + 3% - 1%, + 3% Flame spread classification max 25; smoke developed max 50. The mean mass loss shall not exceed 5% and none of the individual samples shall exceed 10%. PINK FIBERGLAS Insulation Complies Complies Complies Complies Flame spread: 15 Smoke contributed: < 5 Complies Physical Properties Canadian Construction Materials Centre (CCMC) Product Evaluation PINK FIBERGLAS Thermal Insulation is evaluated as a product meeting requirements of NBC 2005 and CAN/ULC-S702. Data valid for products manufactured at facilities in Edmonton (Alberta), Scarborough (Ontario) and Candiac (Quebec). Product Evaluation Listing Number 05650-L. Certification by Independent Third Party Agencies - Recycled Content and Indoor Air Quality Standards SCS Certification (Scientific Certification Systems) for recycled materials content. Certification based on environmental claims certification program: 35% minimum certified recycled materials content distributed as follows: - 26% "post-industrial" (or "preconsumer") recycled materials content; average for all North American manufacturing plants; - 9% "post consumer" recycled materials content; Recycled Materials Content Declared by Owens Corning for its Canadian Manufacturing Facilities The average recycled materials content is at least 60% for the following Canadian manufacturing facilities: Candiac (Quebec): -0% "post-industrial" (or "preconsumer") recycled materials; -60+% "post-consumer" recycled materials. Scarborough (Ontario): -10% "post-industrial" (or "preconsumer") recycled materials; -50+% "post-consumer" recycled materials. Edmonton (Alberta): -0% "post-industrial" (or "preconsumer") recycled materials; -60+% "post-consumer" recycled materials. "Certificate of Achievement": "manufactured by Owens Corning (various forms and sizes)". For up-to-date Certification information go to www.scscertified.com. PINK FIBERGLAS Thermal Insulation is GREENGUARD Certified to meet stringent indoor air quality standards. Certification is in accordance with the GREENGUARD Standard for Low Emitting Products: Individual VOCs 0.1 TLV Formaldehyde 0.02 ppm Total VOCs 0.50 mg/m3 Total aldehydes 0.1 ppm Respirable particles 0.05 mg/m3 "GREENGUARD Indoor Air Quality Certified" certification: Owens Corning PINK FIBERGLAS Thermal Insulation. For up-to-date Certification information go to www.greenguard.org. (1) Refer to the LEED - Green Building Rating System for new construction and important renovations, LEED Canada-NC 1.0, as promoted by the CaGBC. (2) Model National Energy Code for Buildings 1997. (3) The recycled content of a material or furniture must be determined by dividing the weight of the recycled content of the item by the total weight of the whole item, then by multiplying the resulting ratio by the total cost of the item. 07 21 16.16.OCC PINK FIBERGLAS Thermal Batt Insulation Product Data Sheet Consult the Product Safety Data Sheet (MSDS) (see above). Preparation Where there are soffit vents, take appropriate measures to prevent thermal batt insulation from blocking the air ventilation. Install Owens Corning raft-R-mate attic vents. Ensure cavities to be insulated have been inspected, notably: The installation of the support materials located on the cold side (plywood or gypsum boards or other sheathing type panels). Mechanical and electrical service lines passing in or through the wall cavities. Installation Blanket-type insulation must be installed so that at least one face is in full and continuous contact with cladding, sheathing, or some other membrane. Where blanket-type Category and performance criteria EA (Energy and Atmosphere) Credit 1 for energy performance optimization of new or existing buildings. MR (Materials and Resources) Credits 4.1 & 4.2 for recycled materials content.(3) MR (Materials and Resources) Credits 5.1 & 5.2 for locally or regionally produced materials. ID (Innovation & Design Process) Credit 1. Requirements to meet to obtain a voluntary credit Anticipated energy cost reduction compared to NMECB(2) and ASHRAE / IESNA 90.1-1999: 1 to 10 points, based on % reduction. "Post-consumer" recycled content plus one half "post-industrial" recycled materials: 1 point for at least 7.5% and 2 points for at least 15%. Materials regionally extracted and manufactured: 1 point for at least 10% and 2 points for at least 20%. 1-4 points dependent on effectiveness of the innovation being applied. Insulation's contribution to the performance Insulation contributes significantly to the reduction of a building's energy demand. Global contribution depends on the design RSI value. PINK FIBERGLAS Thermal Batt Insulation (Candiac 0% post-industrial, 60+% post-consumer; Scarborough 10% post-industrial, 50+% post-consumer; Edmonton 0% post-industrial, 60+% post-consumer). Canadian insulation products originating from the 3 glass fibre plants (Candiac, Scarborough, Edmonton) contribute towards credits for this category. Glass fibre thermal insulation is also effective in reducing noise transfer through building assemblies. Additional comments The Project Manager is responsible for the energy analysis concerning the global energy efficiency of the building (ex. LEED standard form letter). Recycled content certifications by Scientific Certification Systems for PINK FIBERGLAS Thermal Batt Insulation (>35% North American average and >60 for Canada). Verify with local sales representatives to determine the product's origin. Check with local technical representative for product applications. CONTRIBUTION TO LEED CANADA CERTIFICATION TABLE 2: Contribution of Owens Corning Canada's PINK FIBERGLAS Thermal Batt Insulation Toward LEED CANADA-NC credits(1). IDENTIFICATION AND AVAILABLE SIZES Package Identification Each bag of insulation is labelled with information as required by CAN/ULC-S702 along with the CCMC Evaluation Listing Number 05056-L. APPLICATION Safety Measures: Applicator Protection Ensure applicator's personnel wears protection equipment such as breathing masks (dust-proof type masks prescribed in Material Safety Data Sheet), face and eye protection (safety goggles or eye glasses) and skin protection (gloves, long-sleeved shirts and pants). 30.0 46.0 42.7 64.0 37.3 56.0 26.7 40.0 381 381 584 584 406 610 381 584 381 381 483 584 584 406 610 375 578 406 610 381 584 406 610 406 610 406 610 THERMAL RESISTANCE APPLICATION THICKNESS WIDTH LENGTH COVERAGE/BAG RSI 2.1 2.46 3.5 3.87 4.9 5.4 6.1 12 14 20 22 28 31 35 WOOD FRAME WOOD FRAME STEEL FRAME WOOD FRAME WOOD FRAME STEEL FRAME UNRESTRICTED CAVITY CAVITY RESTRICTED UNRESTRICTED CAVITY UNRESTRICTED CAVITY 89 89 92 152 140 216 178 241 267 3.5 3.5 3.63 6 5.5 8.5 7 9.5 10.5 TABLE 3 - Typical Physical Properties & Coverage R mm in. mm in. 15 15 23 23 16 24 15 23 15 15 19 23 23 16 24 14.75 22.75 16 24 15 23 16 24 16 24 16 24 mm 1194 1219 1194 1219 1219 1219 1194 1194 1194 1219 1194 1194 1219 1219 1219 1194 1194 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 in. 2.79 4.27 3.96 5.95 3.47 5.20 2.48 3.72 ft(2) 7.0 40 UNRESTRICTED CAVITY 279 11 * R12 and R20 48" long batts for wood frame construction are available in QuÈbec only ^ coverage based on SpaceSaver packaging format insulation is installed in attics under flat or sloped roofs, or between rafters in cathedral ceilings, provide at least 65 mm (2 1/2") air space between the cold side of the insulation blanket and the roof deck above. Humidity Wet insulation must be replaced or left to dry by providing an adequate air circulation. If the insulation is not compressed, it will recover its initial thermal resistance. AVAILABILITY AND COST Cost Estimates Cost estimates are readily available from a physical description consisting of drawings and a brief specification based on the information contained in this Product Data Sheet. TECHNICAL SERVICES Owens Corning regional technical support representatives can assist with technical questions. QUALITY CONTROL Owens Corning regularly submits its products to independent agencies that cer tify their environmental quality in terms of: Toxic chemical and volatile particle emissions affecting indoor air quality and the ozone layer. Recycled materials content. INFORMATION CLASSIFICATION SYSTEM Architectural Specifications Classification in accordance with MasterFormatTM 2004 (level 4) published by CSC-DCC and CSI. Selected number and title are 07 21 16.16 ñ Glass Fibre Blanket Insulation. Data Sheet Classification in accordance with MasterFormat 2004 (level 5) published by CSC-DCC and CSI. Selected number 07 21 16.16.OCC PINK FIBERGLAS corresponds to Owens Corning Canada's classification for PINK FIBERGLAS thermal blanket insulation. Product Data Sheet 07 21 16.16.OCC PINK FIBERGLAS Thermal Batt Insulation Publication # 200020 Printed in Canada February 2007 THE PINK PANTHER & 1964-2007 Metro-Goldwyn-Mayer Studios Inc. All Rights Reserved. GREENGUARD Indoor Air Quality Certified is Reg. U.S. Pat & TM Office. MasterFormat is a trademark of the Construction Specifications Institute, Inc. LEED is a trademark of U.S. Green Building Council. The colour PINK is a registered trademark of Owens Corning. 2006-2007 Owens Corning. All Rights Reserved. OWENS CORNING CANADA Head office and sales 3450 McNicoll Avenue, Scarborough, Ontario M1V 1Z5 Tel: 1 (800) 504-8294 Fax: 1 (800) 504-9698 e-mail: salvatore.ciarlo@owenscorning.com web site: www.owenscorning.ca
</font></p>
</body>]]>