<![CDATA[<body bgcolor="#FCE9F2">
<p><font color="#FCE9F2" size="-4">
PRODUCT DESCRIPTION Blown glass fibre thermal insulation, designed for blowing application using commercial pneumatic equipment. Recommended Uses Thermal insulation applied on horizontal surfaces using pneumatic equipment: Attics (or roof-spaces) of flat or sloped roofs, located above flat ceilings or those with a maximum slope of 4.5 : 12 Building floors separating interior from exterior spaces Acoustical insulation for interior floors separating two areas with an acoustic barrier. PROPINK Blown Glass Fibre Insulation is GREENGUARD and SCS certified for its "green" content (refer to TECHNICAL DATA) and can contribute to obtain LEEDô CANADA-NC Certification credits when used as thermal insulation in a building submitted to the LEED CANADA-NC 1.0 - Green Building Rating System (refer to TABLE 2). TECHNICAL DATA Applicable Codes and Standards National Building Code of Canada 1995 Meets requirements of article 9.25.2.2. and 5.3.1.2.(2) (including all subsequent revisions) Canadian Standards CAN/ULC-S702, Standard for Thermal Insulation, Mineral Fibre, for Buildings (supersedes CSA A101-M1983); Type 5, blowing wool CAN/ULC-S102.2, Standard Method of Test for Surface Burning Characteristics of Flooring, Floor Covering and Miscellaneous Materials and assemblies; superficial combustion characteristics; flame spread: 0 and smoke contribution < 5 CAN/ULC S-129, Standard Method of Test for Smoulder Resistance of Blown Insulation (Basket Method) (supersedes ULC-C723(s)): smoulder resistance indicated in CSA A101- M1983) CAN4-S114-M80, Standard test method to determine the noncombustibility of building materials; all Owens Corning blown glass fibre insulation meets the requirements of this standard Health Canada/Workplace Hazardous Materials Information System (WHMIS). Visit www.owenscorning.ca for a current copy of the Material Safety Data Sheet (MSDS) for PROPINK Blown Glass Fibre Insulation. Limitations Owens Corning Canada Inc. does not recommend using PROPINK Blown Glass Fibre Insulation in the following locations: Roof-spaces with ceilings having a slope greater than 4.5 : 12. Wood or steel framed walls in new or existing buildings, whether above or below ground. In such cases, PINK FIBERGLAS Thermal Batt Insulation can be used (refer to Data Sheet 07 2116.16.OCC PINK FIBERGLAS Thermal Batt Insulation). Components PINK colour and glass fibre, manufactured from recycled materials obtained from two sources: "Post-industrial" (or "preconsumer"): glass recycled from glass manufacturing plants' waste (glass containers, flat glass and others). "Post-consumer": glass materials recycled from construction sites (demolition work, new construction and renovation) and from consumers' "blue boxes". Includes materials that contribute to the reduction of dust and static electricity, ensuring a clean and easy installation. This product does not include any phenol-formaldehyde bonding agent. PROPINK Blown Glass Fibre Insulation contains no perlite, vermiculite or phenol-formaldehyde binder. Product Data Sheet 07 21 26.16.OCC PROPINK Blown Glass Fibre Insulation
Canadian Construction Materials Centre (CCMC) Product Evaluation PROPINK Blown Glass Fibre Insulation's design thermal resistance is 20.59 (m2oK/W)/ meter thickness for a design density of 11.21 kg/m3. Data valid for products manufactured at facilities located at 831 Hayter St., Edmonton (Alberta) and at 3450, McNicoll Avenue, Scarborough (Ontario). Product Evaluation Listing Number 12851-L. Certification by Independent Third Party Agencies - Recycled Content and Indoor Air Quality Standards SCS Certification (Scientific Certification Systems) for recycled materials content. Certification based on environmental claims certification program: 35% minimum certified recycled materials content distributed as follows: - 26% "post-industrial" (or "preconsumer") recycled materials content; average for all North American manufacturing plants; - 9 % "post consumer" recycled materials content; PROPINK Blown Glass Fibre Insulation is GREENGUARD Certified to meet stringent indoor air quality standards. Certification is in accordance with the GREENGUARD Standard for Low Emitting Products: Individual VOCs 0.1 TLV Formaldehyde 0.02 ppm Total VOCs 0.50 mg/m3 Total aldehydes 0.1 ppm Respirable particles 0.05 mg/m3 "GREENGUARD Indoor Air Quality Certified" certification: Owens Corning PROPINK Blown Glass Fibre Insulation. For up-to-date Certification information, go to www.greenguard.org. "Certificate of Achievement": "manufactured by Owens Corning (various forms and sizes)". For up-to-date Certification information, go to www.scscertified.com. Product Data Sheet 07 21 26.16.OCC PROPINK Blown Glass Fibre Insulation Properties CAN/ULC-S702 requirements for for blowing wool(1) PROPINK Blown Glass Fibre Insulation Design density Thermal resistivity Surface burning characteristics Smoulder resistance Design density. 18.5 (m2oK)/W or greater than manufacturer's stated thickness per unit area. Flame spread classification max. 25; smoke developed max. 50. Mean loss of mass 5% for three samples and 10% for each sample. 11.21 kg/m3 20.59 (m2oK)/W / meter of thickness. Flame spread : 0 Smoke developed: 5. Meets requirements of the standard. TABLE 1 Physical Properties (1) Refer to CAN/ULC-S702, TABLE 2 (1) Refer to the LEED- Green Building Rating System for new construction and important renovations, LEED Canada-NC 1.0, as promoted by the CaGBC. (2) Model National Energy Code for Buildings 1997. (3) The recycled content of a material or furniture must be determined by dividing the weight of the recycled content of the item by the total weight of the whole item, then by multiplying the resulting ratio by the total cost of the item. Category and performance criteria EA (Energy and Atmosphere) Credit 1 for energy performance optimization of new or existing buildings. MR (Materials and Resources) Credits 4.1 & 4.2 for recycled materials content.(3) MR (Materials and Resources) Credits 5.1 & 5.2 for locally or regionally produced materials. ID (Innovation & Design Process) Credit 1. Requirements to meet to obtain a voluntary credit Anticipated energy cost reduction compared to NMECB(2) and ASHRAE / IESNA 90.1-1999 m: 1 to 10 points, based on % reduction. "Post-consumer" recycled content plus one half "post-industrial" recycled materials: 1 point for at least 7.5% and 2 points for at least 15%. Materials regionally extracted and manufactured: 1 point for at least 10% and 2 points for at least 20%. 1-4 points dependent on effectiveness of innovation being applied. Insulation's contribution to the performance Insulation contributes significantly to the reduction of a building's energy demand. Global contribution depends on the design RSI value. PROPINK Blown Glass Fibre Insulation: (Edmonton 60+% postconsumer, 0% postindustrial; Toronto 50+% post-consumer, 10% post-industrial). Canadian Insulation products originating from the 2 FIBERGLAS plants (Toronto, Edmonton) contribute towards credits for this category. Glass Fibre Insulation is effective in reducing noise transfer through building assemblies. Additional comments The Project Manager is responsible for the energy analysis concerning the global energy efficiency of the building (ex. LEED standard form letter). Recycled content certifications by Scientific Certification Systems for PROPINK Glass Fibre Insulation (>35% North American average and >60% for Canada). Verify with local sales representatives to determine the product's origin. Verify with local technical representative for product applications. CONTRIBUTION TO LEED CANADA CERTIFICATION TABLE 2: Contribution of Owens Corning Canada's PROPINK Blown Glass Fibre Insulation towards LEED CANADA-NC credits(1)
Recycled materials content declared by Owens Corning for its Canadian manufacturing facilities The average recycled materials content is at least 60% for the following Canadian manufacturing facilities: Toronto (Ontario): - 10% "post-industrial" (or "preconsumer") recycled materials; - 50+% "post-consumer" recycled materials. Edmonton (Alberta): - 0% "post-industrial" (or "preconsumer") recycled materials; - 60+% "post-consumer" recycled materials. IDENTIFICATION Each bag of insulation is labelled with information as required by CAN/ULC-S702, along with the CCMC evaluation listing number 12851-L. APPLICATION Preparation Where there are soffit vents, take appropriate measures to prevent blown glass fibre insulation from accumulating and blocking the air ventilation and also to prevent the insulation from being displaced due to wind penetration through the soffit vents. Install Owens Corning raft-R-mate attic vents. Applicator Protection Ensure applicator's personnel wears protection equipment such as breathing masks (dust-proof type masks prescribed in Product Data Sheet), face and eye protection (safety goggles or eye glasses) and skin protection (gloves, long-sleeved shirts and pants). TECHNICAL SERVICES Owens Corning Canada Inc. Regional Technical Support Representatives can assist with technical questions. QUALITY CONTROL Owens Corning Canada Inc. regularly submits its products to independent agencies that certify their environmental quality in terms of: Toxic chemical and volatile particle emissions affecting indoor air quality and the ozone layer. Recycled materials content. A Certificate of Coverage form is available to the applicator to be filled-in and signed in accordance with requirements of CAN/ULCS702; it must be posted on site during the Work and remitted to the Owner. Pneumatic Application Product applied in unconfined spaces with slopes not exceeding 4.5: 12 and in accordance with manufacturer's data illustrated in the following APPLICATION CHART. Humidity Wet insulation must be replaced or left to dry by providing an adequate air circulation. If the insulation is not compressed, it will recover its initial thermal resistance. AVAILABILITY AND COST Cost Estimates Cost estimates are readily available from a physical description consisting of drawings and a brief specification based on the information contained in this Product Data Sheet. Product Data Sheet 07 21 26.16.OCC PROPINK Blown Glass Fibre Insulation (1) Measured at locations where thickness is not limited by roof slope nor other obstacles. (2) Net coverage per bag may be increased 2% to 10% according to joist spacing and dimensions. Use correction factors to determine exact percentage. THERMAL RESISTANCE RSI R 1.9 2.1 2.8 3.3 3.5 3.8 4.2 4.9 5.3 5.6 6.0 6.3 6.7 7.0 7.7 8.4 8.6 8.8 9.1 9.8 10.5 11 12 16 19 20 22 24 28 30 32 34 36 38 40 44 48 49 50 52 56 60 92 102 136 160 170 185 204 238 257 272 291 306 325 340 374 408 418 427 442 476 510 3 3/4 4 5 1/4 6 1/4 6 3/4 7 1/4 8 9 1/4 10 1/4 10 3/4 11 1/2 12 12 3/4 13 1/2 14 3/4 16 16 1/2 16 3/4 17 1/2 18 3/4 20 15.3 13.9 10.4 8.8 8.3 7.7 6.9 5.9 5.5 5.2 4.9 4.6 4.4 4.2 3.8 3.5 3.4 3.3 3.2 3.0 2.8 165.1 149.4 112.0 95.1 89.6 82.6 74.7 64.0 59.2 56.0 52.3 49.8 46.8 44.8 40.7 37.3 36.5 35.7 34.5 32.0 29.9 6.5 7.2 9.6 11.3 12.0 13.0 14.4 16.8 18.2 19.2 20.6 21.6 23.0 24.0 26.4 28.8 29.5 30.2 31.2 33.6 36.0 6.1 6.7 8.9 10.5 11.2 12.1 13.4 15.6 16.9 17.8 19.1 20.1 21.4 22.3 24.5 26.8 27.4 28.0 29.0 31.2 33.5 1.03 1.14 1.52 1.80 1.91 2.07 2.29 2.67 2.89 3.05 3.27 3.43 3.65 3.81 4.19 4.57 4.68 4.79 4.95 5.33 5.72 0.21 0.23 0.31 0.37 0.39 0.42 0.47 0,55 0.59 0.62 0.67 0.70 0.75 0.78 0.86 0.94 0.96 0.98 1.01 1.09 1.17 MINIMUM THICKNESS(1) mm inch MAXIMUM COVERAGE PER BAG 15.9 kg /35 lb(2) m2 ft2 MINIMUM NUMBER OF BAGS PER UNIT OF AREA 100 m2 1000 ft2 MINIMUM WEIGHT PER UNIT OF AREA kg/m2 lb/ft2 TABLE 3 - APPLICATION CHART
The certificate shall include the following information and statements: A. product/brand name; B. manufacturer's name and address; C. area insulated; D. net bag content; E. applied thickness; F. calculated number of bags required; G. number of bags installed; H. thermal resistance of the applied insulation; I. date installed; J. applicator's name and signature; K. applicator's company name and address; and L. applicable certification number or CCMC number. The Certificate of Coverage form must be accompanied by the application chart as required by the standard; refer to Table 3, article 7 - Application. INFORMATION CLASSIFICATION SYSTEM Architectural Specifications Classification in accordance with MasterFormatTM 2004 (level 4) published by CSC-DCC and CSI. Selected number and title is 07 21 26.16 ñ Blown Glass Fibre Insulation. Data Sheet Classification in accordance with MasterFormat 2004 (level 5) published by CSC-DCC and CSI. Selected number 07 21 26.16.OCC PROPINK Blown Glass Fibre Insulation corresponds to the classification of the PROPINK Blown Glass Fibre Insulation manufactured by Owens Corning Canada (OCC) Inc. Product Data Sheet 07 21 26.16.OCC PROPINK Blown Glass Fibre Insulation Publication # 200019 Printed in Canada May 2006 THE PINK PANTHERô & 1964-2006 Metro-Goldwyn-Mayer Studios Inc. All Rights Reserved. GREENGUARD Indoor Air Quality Certified is Reg. U.S. Pat & TM Office. MasterFormat is a trademark of the Construction Specifications Institute, Inc. LEED is a trademark of U.S. Green Building Council. The colour PINK is a registered trademark of Owens Corning Canada, Inc. 2006 Owens Corning Canada, Inc. All Rights Reserved. OWENS CORNING CANADA INC. Head office and sales 3450 McNicoll Avenue Scarborough, Ontario M1V 1Z5 Tel: 1 (800) 988-5269 Fax: 1 (800) 989-8298 e-mail: keith.wilson@owenscorning.com Tel: 1 (800) 504-8294 Fax: 1 (800) 504-9698 e-mail: salvatore.ciarlo@owenscorning.com web site: www.owenscorning.ca
</font></p>
</body>]]>